网红主播精品视频在线观看_草久在线播放_免费人成在线观看成人片_国产高清乱子精品偷伦对白_国产无遮挡色视频免费观看性色_亚洲精品色婷婷在线影院

產品推薦:水表|流量計|壓力變送器|熱電偶|液位計|冷熱沖擊試驗箱|水質分析|光譜儀|試驗機|試驗箱


儀表網>技術中心>分析方法>正文

歡迎聯系我

有什么可以幫您? 在線咨詢

閥門大小的確定VALVE SIZING

來源:常熟市常陽儀表科技有限公司   2008年03月25日 09:36  

閥門大小的確定VALVE SIZING

      

  為了正確選擇自動控制閥的通徑,用戶需要了解下列事項:
  To properly size an automatic control valve you need to know the following:

  • Z和Z低的進口壓力
    HighestLowest inlet pressures
  • 出口壓力
    Outlet pressure
  • Z大流量要求
    Maximum flow requirements
  • Z小流量要求
    Minimum flow requirements

  步驟1:利用流量表,并且在橫軸上找出符合用戶Z大流量要求的流量值。
  Step 1: Utilize the high flow chartthe flow as found on the horizontal axis which corresponds with your maximum flow requirements.
  步驟2:從這一點劃垂線,延伸到與相應的Z小壓差的水平線相交。(此時,Z小壓差將是Z低進口壓力減去所需要的出口壓力,這也就是所說的P。)
  Step 2: From this point draw a vertical line until you intersect with the horizontal line corresponding with the minimum differential pressure. Your minimum differential pressure will be the lowest inlet pressure minus the desired outlet pressure, this is also known as the delta P.
  步驟3:從這一點向右移動直到*個閥門的通徑線。這就是在25英尺/秒間歇流量時應該采用的Z小閥門通徑。如果Z大流量是連續的,那么不要超過Z大連續流量表上所列的美制加侖/分鐘(20英尺/秒)。
  Step 3: From this point move right to the first valve size line. This will be the minimum valve size which should be used on intermittent flow of 25 ft./sec. If maximum flow is continuous, then do not exceed the GPM 20 FT./sec. listed on the maximum continuous flow table.

 

  步驟4:利用流量表,在豎軸上找到Z大壓差。(用戶的Z大壓差將是Z進口壓力減去所需要的出口壓力,這也就是所說的P。)
  Step 4: Utilize the flow chartthe maximum differential pressure as found on the vertical axis. Your maximum differential pressure will be the highest inlet pressure minus the desired outlet pressure, this is also known as the delta P.
  步驟5:從這一點劃水平線與步驟3選擇的閥門通徑相應的線相交。
  Step 5: From this point draw a horizontal line until you intersect with the line corresponding to the valve size as selected in step 3.
  步驟6:從這一點劃垂線向下與橫軸相交。這就是以這些變量為基礎的閥門的Z小流量能力
  Step 6: From this point draw a vertical line down to the horizontal axis. This will be the minimum flow capabilities of the valve based on these variables.
  注意:1 如果通過步驟6得到的Z小流量能力比用戶實際的Z小流量要求,則用戶應該考慮采用并聯安裝方式。采用這個Z小流量能力,從步驟1開始選擇用戶需要的用于低流量旁路的通徑。
     2 采用空穴圖表并且確定進口和出口壓力的相交是否落在陰影區域內。如果是,用戶應該考慮串聯安裝方式。兩個閥門都應該按照上述步驟選擇通徑。
  Notes: 1 If the minimum flow capability obtained from step 6 is above your actual minimum flow requirements, you should consider a parallel installation. Using the minimum flow capability, begin at step 1 to the size you will need for this low-flow by-pass.
     2 Use the cavitation chartdetermine if the intersection of the inletoutlet pressures falls in the shaded area. If so, you should consider a series installation. Both valves should be sized in accordance with the above steps.

 
Z小連續流量表
MAXIMUM CONTINUOUS FLOW CHART
通徑
SIZE
11/4"11/2"2"21/2"3"4"6"8"10"12"14"16"
流量(美制加侖/分鐘)
FLOW GPM
93932103004608001800310049007000850011000
  
流量表(Z大間歇流量)
HIGH FLOW CHART MAXIMUM INTERMITTENT FLOW
P = Z小壓差
P = minimum pressure difference
  
低流量表(Z小間歇流量)
LOW FLOW CHART MINIMUM INTERMITTENT FLOW
P = Z小壓差
P = minimum pressure difference

美制加侖/分鐘
USGPM

壓降指數 - 減壓閥
PRESSURE DROP INDEX - PRESSURE REDUCING VALVES

  通過從Z大進口壓力減去所需要的出口壓力來計算壓差。找出壓差線上的數字,并且注意出口壓力指數。這是不會落入空穴區的Z低的出口壓力設置。美瓦茨自動控制閥的結構將可能導致空穴現象的閥門損壞潛在危險降低到Z小程度。避免在空穴區域內持續運行。
  Calculate the pressure difference by subtracting the desired outlet pressure from the maximum inlet pressure. Find the number on the pressure difference linenote the outlet pressure index number. This is the lowest outlet pressure setting allowed without failing into the cavitation zone. Design of the WATTS Automatic Control Valve minimizes potential valve damage that can be caused by cavitation. Avoid continued operation within the cavitation zone.

 
壓差(PSIG)
PRESSURE DIFFERENCE PSIG
102030405060708090100125150175200
出口壓力指數(Z低出口壓力設置,PSIG)
OUTLET PRESSURE INDEX Lowest Outlet Setting, PSIG
00038142025313751657993
 

空穴圖表
CAVITATION CHART

  閥門通徑選擇后,在這個圖表中找出進口和出口壓力。如果交點落在陰影區域,則可能產生空穴。應該避免在空穴區域內持續運行閥門。請咨詢美瓦茨ACV,了解其他解決方案。
  After selecting valve size, locate inletoutlet pressures on this chart. If the intersection point falls in the shaded area, cavitation can occur. Operation of valves continually in the cavitation zone should be avoided. Consult Watts ACV for alternatives.

 

出口壓力 - PSI
OUTLET PRESSURE - PSI

免責聲明

  • 凡本網注明“來源:儀表網”的所有作品,均為浙江興旺寶明通網絡有限公司-儀表網合法擁有版權或有權使用的作品,未經本網授權不得轉載、摘編或利用其它方式使用上述作品。已經本網授權使用作品的,應在授權范圍內使用,并注明“來源:儀表網”。違反上述聲明者,本網將追究其相關法律責任。
  • 本網轉載并注明自其它來源(非儀表網)的作品,目的在于傳遞更多信息,并不代表本網贊同其觀點或和對其真實性負責,不承擔此類作品侵權行為的直接責任及連帶責任。其他媒體、網站或個人從本網轉載時,必須保留本網注明的作品第一來源,并自負版權等法律責任。
  • 如涉及作品內容、版權等問題,請在作品發表之日起一周內與本網聯系,否則視為放棄相關權利。
聯系我們

客服熱線: 13199863987

加盟熱線: 13199863987

媒體合作: 0571-87759945

投訴熱線: 0571-87759942

關注我們
  • 下載儀表站APP

  • Ybzhan手機版

  • Ybzhan公眾號

  • Ybzhan小程序

企業未開通此功能
詳詢客服 : 0571-87759942
主站蜘蛛池模板: 亚洲va无码va在线va天堂 | 国产成人精彩在线视频九色 | 91精品欧美一区二区三区 | v11av在线视频成人 | 国产一区一区三区 | 吴梦梦在线看 | 国产精品第10页 | xxxx亚洲 | 沦为公交两奶头春药高潮迭起 | 中文字幕一区二区三区精品 | 在线观看免费一级片 | 亚洲网站www | 性无码专区无码片 | 91精品视频网站 | 亚洲国产精品嫩草影院 | youjizzcom中国熟妇 | 亚洲国产wwwccc36天堂 | 西西人体www大胆高清仙踪林 | 国产免费人成在线视频 | 天天躁日日躁狠狠躁欧美老妇小说 | 日本无遮挡在线观看 | 国产农村一级国产农村 | 少年巨茎征服熟女系列 | 欧美精品久久久免费观看 | 婷婷色香五月综合激激情 | 蜜桃精品一区二区 | 成年免费视频 | 久久里面有精品 | 国产色婷婷五月精品综合在线 | 中国CHINA体内裑精亚洲日本 | 亚洲精品午夜视频 | 日本二区三区 | 狠狠狠干 | 超碰在线资源 | 剑来56集全免费播放 | 欧美久操视频 | 人妻无码αv中文字幕久久琪琪布 | 天天狠天天情天天躁 | 精品无人区卡一卡二卡三 | 久久久久久狠狠综合一本 | 超碰公开在线 |