進入展臺 在線留言

歡迎聯系我

有什么可以幫您？在線咨詢

詳細闡述德國DIN EN ISO11997-1循環腐蝕測試標準的試驗方法和步驟

來源：東莞市科迪儀器有限公司 2025年05月10日 07:21

德國DIN EN ISO11997-1循環腐蝕測試標準及復合鹽霧測試方法

Cycle A

C.1 Salt fog test solution鹽霧試驗溶液

Prepare the spray solution as described in Clause 5 by dissolving sodium chloride in water to give a concentration of (50±10)g/l .The PH of the solution shall be in the range 6 to 7.
按照第5條所述的方法制備噴霧溶液，將氯化鈉溶解在水中，使溶液的濃度為（50±10）g/L，溶液的pH值在6～7范圍內。

C.2 Cycle

Set up the cabinet to perform the following cycle設置鹽霧箱執行以下循環

Step	Time h	Temp ℃	Condition	Notes
1	2	35±2	Salt spray
2	4	60±2	Dry：20-30%
3	2	50±2	Wet：95%RH or over
4	Go back to step 1			This makes a total cycle time of 8h from step1 to step3
	Transtition time（ie time allowed to reach the temperature and relative humidity specified for a condition after changing to that condition）：			From salt spray to dry：within 30min 從鹽霧到干燥：30min內 From dry to wet：within 150 min 從干到濕：150分鐘內 From wet to salt spray：within 30min 從濕到鹽霧：30分鐘內 The effect of the salt spray will，in principle，be instaneous。 For details of drying-air flow，see 6.4 鹽霧的效果在原則上是瞬時的。有關干燥空氣流量的詳細信息，請參見6.4

C.3 Salt fog depsiton rate鹽霧沉降率

The salt fog deposition rate shall be 1ml/h to 2ml/h,when the salt fog iscollected over a 24h period (see Clause 10)
當鹽霧在24小時內被收集時，鹽霧的沉積速率應該是1ml/h到2ml/h（見第10條）

C 4 Duration持續時間

Unless otherwise agreed，repeat the test cycle for 30 cycles(240h),60cycles(240h),90cycles(720h) or 180cycles(1440h)
除非另有約定，重復測試周期30周期（240h）、60周期（240h）、90周期（720h）或180周期（1440h）

Cycle B

C.1 Salt fog test solution鹽霧試驗溶液

C.2 Cycle

Set up the cabinet to perform the following cycle. 設置鹽霧箱執行以下循環。

Step	Time h	Temp ℃	Condition	notes
1	24	35±2	Salt fog
2	8	40±2	99%RH	Water condensing on test panels
3	16	23±2	（50±20）%RH
4	8	40±2	99%RH	Water condensing on test panels
5	16	23±2	（50±20）%RH
6	8	40±2	99%RH	Water condensing on test panels
7	16	23±2	（50±20）%RH
8	8	40±2	99%RH	Water condensing on test panels
9	16	23±2	（50±20）%RH
10	48	23±2	（50±20）%RH
11	Go back to step 1			This makes the total cycle time 7 days from step1 to step10.
NOTE Set points and operational fluctuations can be listed either independently of each other or in the format：set point±operational fluctuations.The set point is the target condition for the sensor when used at the operational control point as programmed by the user.Operational fluctuations are deviations from the indicated set point at the control point indicated by the readout of the calibrated control sensor during equilibrium operation and do not include measurement uncertainty.At the operational control point , the user programmes that exat number . The operational fluctuations specified for that set point do not imply that the user is allowed to programme a set point higher or lower than the exact set point specified.

C 3 Salt fog depsiton rate鹽霧沉降率

The salt fog deposition rate shall be 1ml/h to 2ml/h,when the salt fog iscollected over a 24h period (see Clause 10)

C 4 Duration持續時間

Unless otherwise agreed，repeat the test cycle for 840 h
除非另有約定，重復測試周期為840小時。

Cycle C

C.1 Salt fog test solution鹽霧試驗溶液

Prepare the spray solution as described in Clause 5 by dissolving sodium chloride in water to give a concentration of (0.31±0.01)g/l and (4.1±0.01)g/l respectively .The PH of the solution shall be in the range 6 to 7.
按照第5條所述的方法制備噴霧溶液，在水中溶解氯化鈉，濃度分別為（0.31±0.01）g/L和（4.1±0.01）g/L，溶液的pH值在6～7范圍內。

C.2 Cycle

Set up the cabinet to perform the following cycle. 設置來執行以下循環。

Step	Time min	Temp ℃	Condition	notes
1	210	30±2	Salt fog
2	210	40±2	Dry	Drying-air purge(see 6.4)
3	1470	40±2	（75±15）%RH	One method of achieving this conditon is to alternate the dry and humid cycles for suitable(short)time periods to keep the RH between the limits specified
4	102	30±2	Dry	Drying-air purge(see 6.4)
5	210	30±2	Salt fog
6	378	30±2	90% to 99%RH	Water condensing on test panel
7	180	35±2	Dry	Drying-air purge(see 6.4)
8	120	25±2	Dry
9	Go back to step 1			This makes the total cycle time 48h from step1 to step8.
NOTE Set points and operational fluctuations can be listed either independently of each other or in the format：set point±operational fluctuations.The set point is the target condition for the sensor when used at the operational control point as programmed by the user.Operational fluctuations are deviations from the indicated set point at the control point indicated by the readout of the calibrated control sensor during equilibrium operation and do not include measurement uncertainty.At the operational control point , the user programmes that exat number . The operational fluctuations specified for that set point do not imply that the user is allowed to programme a set point higher or lower than the exact set point specified.

C 3 Salt fog depsiton rate鹽霧沉降率

The salt fog deposition rate shall be 2ml/h to 4ml/h,when the salt fog iscollected over a 24h period (see Clause 10)
當鹽霧在24小時內被收集時，鹽霧的沉積速率應為2ml/h至4ml/h(見第10條)。

C 4 Duration持續時間

Unless otherwise agreed，repeat the test cycle for1000h
除非另有約定，重復測試周期為1000小時。

Cycle D

C.1 Salt fog test solution鹽霧試驗溶液

C.2 Cycle

Set up the cabinet to perform the following cycle，設置執行如下下循環

Step	Time h	Temp ℃	Condition	Notes
1	0.5	30±2	Salt spray
2	1.5	30±2	Wet：（95±3）%RH
3	2	50±2	Hot dry
4	2	30±2	Warm dry
5	Go back to step 1			This makes a total cycle time of 6h from step1 to step4
	Transtition time（ie time allowed to reach the temperature and relative humidity specified for a condition after changing to that condition）：			From salt spray to wet：within 10min 從鹽霧到潮濕：10min以內 From wet to hot dry：within 15 min 從濕到熱干燥：15分鐘內 From hot dry to salt warm dry：within 30min 從熱干燥到鹽溫干燥：30min內 From salt warm dry to salt spray：instaneous 從鹽溫干到鹽霧：瞬時
NOTE Set points and operational fluctuations can be listed either independently of each other or in the format：set point±operational fluctuations.The set point is the target condition for the sensor when used at the operational control point as programmed by the user.Operational fluctuations are deviations from the indicated set point at the control point indicated by the readout of the calibrated control sensor during equilibrium operation and do not include measurement uncertainty.At the operational control point , the user programmes that exat number . The operational fluctuations specified for that set point do not imply that the user is allowed to programme a set point higher or lower than the exact set point specified.

C 3 Salt fog depsiton rate鹽霧排放率

C 4 Duration持續時間

Unless otherwise agreed，repeat the test cycle for 28 cycles(168h)
除非另有約定，重復測試周期為28個周期（168h）。

符合德國DIN EN ISO11997-1測試標準的循環腐蝕復合鹽霧箱

參考文章：
1、CETP 0000-L-467試驗室加速循環腐蝕試驗標準中文翻譯版
2、淺析福特汽車CETP 0000-L-467測試標準的試驗步驟及方法
3、簡析通用汽車GMW 1487標準的試驗流程及步驟

相關產品

免責聲明

凡本網注明“來源：儀表網”的所有作品，均為浙江興旺寶明通網絡有限公司-儀表網合法擁有版權或有權使用的作品，未經本網授權不得轉載、摘編或利用其它方式使用上述作品。已經本網授權使用作品的，應在授權范圍內使用，并注明“來源：儀表網”。違反上述聲明者，本網將追究其相關法律責任。
本網轉載并注明自其它來源（非儀表網）的作品，目的在于傳遞更多信息，并不代表本網贊同其觀點或和對其真實性負責，不承擔此類作品侵權行為的直接責任及連帶責任。其他媒體、網站或個人從本網轉載時，必須保留本網注明的作品第一來源，并自負版權等法律責任。
如涉及作品內容、版權等問題，請?jiān)谧髌钒l(fā)表之日起一周內與本網聯系，否則視為放棄相關權利。

网红主播精品视频在线观看_草久在线播放_免费人成在线观看成人片_国产高清乱子精品偷伦对白_国产无遮挡色视频免费观看性色_亚洲精品色婷婷在线影院

詳細闡述德國DIN EN ISO11997-1循環腐蝕測試標準的試驗方法和步驟

德國DIN EN ISO11997-1循環腐蝕測試標準及復合鹽霧測試方法

Cycle A

C.1 Salt fog test solution鹽霧試驗溶液

C.2 Cycle

C.3 Salt fog depsiton rate鹽霧沉降率

C 4 Duration持續時間

Cycle B

C.1 Salt fog test solution鹽霧試驗溶液

C.2 Cycle

C 3 Salt fog depsiton rate鹽霧沉降率

C 4 Duration持續時間

Cycle C

C.1 Salt fog test solution鹽霧試驗溶液

C.2 Cycle

C 3 Salt fog depsiton rate鹽霧沉降率

C 4 Duration持續時間

Cycle D

C.1 Salt fog test solution鹽霧試驗溶液

C.2 Cycle

C 3 Salt fog depsiton rate鹽霧排放率

C 4 Duration持續時間

免責聲明